Verified product catalogue
Choose a product
81 products match
BFC-000171
Dual Plate Check Valve – NBR Seat
Ductile Iron · Wafer · 1 1/2", 10", 12", 14", 16", 18", 2 1/2", 2", 20", 24", 3", 4", 5", 6", 8"
Price: On Application
BFC-000181
Cast Iron Check Valve – Flanged PN16 – Bronze Seat
Cast Iron · PN16 · PN16
Price: On Application
BFC-000187
Stainless Steel Swing Check Valve – Wafer Pattern
Stainless Steel · Wafer · 1 1/2", 10", 12", 14", 16", 2 1/2", 2", 3", 4", 5", 6", 8"
Price: On Application
BFC-000211
Ductile Iron Check Valve – Flanged PN16 – WRAS Approved
Ductile Iron · PN16 · PN16
Price: On Application
BFC-000233
Stainless Steel Dual Plate Check Valve – Wafer Pattern
Stainless Steel · Wafer · PN10/16, PN10
Price: On Application
BFC-000251
Cast Iron Check Valve – Flanged PN16 – EPDM Seat
Cast Iron · PN16 · PN16
Price: On Application
BFC-000309
Stainless Steel Check Valve – Screwed BSPP – 6000psi
Stainless Steel · BSPP · 6000psi, 0.33psi
Price: On Application
BFC-000315
CR Brass Single Check Valve – Compression Ends – WRAS Approved
Brass · Compression Ends · 15mm, 22mm, 28mm
Price: On Application
BFC-000338
Forged Steel Check Valve – Screwed BSPT
Forged Steel · BSPP · Class 800, 136.2 Bar
Price: On Application
BFC-000339
Stainless Steel Swing Check Valve – Flanged PN16
Stainless Steel · PN16 · PN16
Price: On Application
BFC-000343
Stainless Steel Disc Check Valve – Clearance
Stainless Steel · Wafer · PN40
Price: On Application
BFC-000350
Stainless Steel Spring Swing Check Valve – Wafer Pattern
Stainless Steel · Wafer · PN6/10, ANSI 150, PN25, PN16
Price: On Application
BFC-000364
CR Brass Double Check Valve – Compression Ends – WRAS Approved
Brass · Compression Ends · 15mm, 22mm, 28mm
Price: On Application
BFC-000373
Stainless Steel Check Valve – Compression Ends – Imperial
Stainless Steel · Compression Ends · 6000psi, 0.33psi, 000psi
Price: On Application
Technical overview and selection guidance
The valve opens from forward differential pressure and closes when flow decelerates or reverses. Closing dynamics, orientation and minimum velocity matter as much as nominal size.
Where Check Valves fit
Check Valves may be considered where its operating principle, envelope and materials suit the process. Confirm whether the duty is isolation, throttling, diversion, non-return or pressure control; a familiar valve type is not automatically the lowest-risk choice.
Selection checklist
| Factor | What to confirm |
|---|---|
| Process medium | Composition, concentration, solids, viscosity, toxicity and cleaning regime. |
| Pressure and temperature | Normal, design, transient and vacuum conditions against the manufacturer curve. |
| Materials | Body, trim, seat, seals, fasteners and coatings—not body material alone. |
| Connections | Nominal size, bore, flange or thread standard, face-to-face and installation space. |
| Operation | Manual or actuated, cycle rate, closing time, fail action, feedback and utilities. |
| Compliance | Project specification, testing, water, fire-safe or hazardous-area requirements. |
Common specification mistakes
- Quoting only nominal size and pressure class.
- Assuming a material name proves chemical compatibility.
- Ignoring transient pressure, differential pressure or installation orientation.
- Selecting an actuator from running torque alone.
- Treating an approval held by one product variant as applying to the whole range.
Frequently asked questions
Can one pressure rating be applied to every Check Valves?
No. The allowable pressure changes with materials, temperature, design, size and the governing standard. Use the current product pressure-temperature table.
What information is needed for automation?
At minimum: valve make and model, size, differential pressure, measured or published torque/thrust, supply, cycle time, fail action, control signal and environment.